One issue you’ll have to deal with when troubleshooting washing machine problems is that the washer simply won’t start. This can be very frustrating, especially if you have a load of clothes waiting to be washed. In most instances, you should be able to solve the problem easily without having to call in the plumber and spending a lot of money. If your washing machine won’t start, begin by looking at the power source. First of all, is the washer plugged in? If it is, has it tripped a circuit breaker or blown a fuse? Check and reset the breaker (or replace the fuse) if necessary, then try to start the machine again. Also make sure that the door is properly closed. Washing machines will not start when the door is still ajar. The main control for the washing machine is the switch inside the lid. If this has stopped working for some reason, your washer won’t start. It’s not especially difficult to troubleshoot this, however, you might have to open the top to access the lid switch.

With the power on, depress the switch and listen for a click. If you don’t hear one, the switch has gone and will need to be replaced. If the lid switch works but the washing machine still won’t start, check to see if your washing machine has a special fuse for it. It will usually be inside the control panel. If it’s blown, you’ll need to replace it before the washer will start. The problem could be with the door interlock. If the lights come on but the machine won’t start, this might well be the cause. This could either be the wiring that runs to the door interlock, or the door catch not activating the interlock itself. In this instance, you will need to call in a professional to trace and repair the fault. Some models of washing machine use a mechanical timer knob and won’t run until the water in the machine has filled to the selected level. If the knob doesn’t line up properly with the graphics on the control panel, you can try to troubleshoot the washing machine problem by advancing the timer a little.

When you’ve done this, pull it out a little way and see if the washer will start properly. If you’ve run several loads, one after another, without any problem but suddenly find your washing machine refuses to start, overheating could be the cause. The simple way to discover whether this is the problem is to give the machine ample time to cool down, say for a couple of hours, and then try it again. Grohe Kitchen Faucet Install InstructionsIf it works fine, overheating was the case and it should not reoccur as long as you don’t do too many loads in too short of a time.Canadian Tire Bbq CanopyREPAIR > WASHER > WILL NOT STARTMiniature Pinscher Puppies For Sale In Southern California How to Fix A Washer That Won't Start

Start Your Repair Here We have switches for thousands of models MORE ABOUT THIS REPAIR The lid switch on a top load washing machine is a safety device designed to prevent the motor circuit from operating when the lOn some models, the water inlet valve circuit is controlled as well. If the lid switch fails, the washer may not start. The lid switch is normally located beneath the main top with a projection on the lid or a pin attached to the lid that will actuate the switch when the lid is closed. Verify that the switch is being activated mechanically and that any levers or actuators are not damaged or sticking. If the switch is being activated but there is no power being supplied to the motor or water valve circuits, then the switch may be defective. Disconnect power from the appliance and remove the wires from the switch. You can then check the switch for continuity with a multi-meter. We strongly recommend that you DO NOT bypass a lid switch as it is an important safety feature and serious injury could result.

We have door switches for thousands of models A safety feature found on front load washing machine is the door switch and the door lock and strike. On most models, the door switch must be closed and the door lock must be activated before the washer will start. The switch is normally located in the door frame of the washing machine, but may also be part of the door lock assembly. Inspect the strike to make sure that it engages the door lock assembly and that the door remains closed. To check the door switch for continuity with a multi-meter, you will need to disconnect the power and remove the front panel. We have timer switches for thousands of models The start switch on some top load washers is often part of the timer and is activated by pulling out on the timer knob. Although not normally available as a separate part, the switch can be tested for continuity with a multi-meter. You will need to remove power from the appliance and then locate the correct timer contacts as noted on the wiring diagram.

On some electronic controlled models, the start switch is a momentary contact type switch located on the control console. You can test this switch for continuity with a multi-meter when the push button is held in. Remove power from the appliance and at least one of the wires from the switch first. We have knobs for thousands of models On models that use a start switch that is part of the timer, you should also check the timer knob to ensure that it is properly engaging the shaft that operates the switch. Normal wear can cause the knob to slip on the shaft and not be able to engage the switch mechanism. Remove power from the appliance and then access the back of the timer. Visually inspect the shaft to verify that the knob engages it when pulled out and pushed in. We have motors for thousands of models All washing machines use a motor that is responsible for spinning and agitating during the cleaning cycle. Many top load brands use a reversing motor which means the motor spins in one direction for agitating and another for spinning and draining.

If the motor does not start, but makes a humming or buzzing noise then it may be defective. To verify if the motor is at fault, remove the drive and /or pump belts and then try to start the motor again. On direct drive models, you will have to disengage the pump and the direct drive coupling to the transmission. If the motor starts, then the problem is with the transmission or the pump and can be further diagnosed by reconnecting each one individually. If the motor does not start or continues to hum or buzz, then it will need to be replaced. Use caution when working on or near the motor as there are live electrical circuits and moving parts. On front load washers the motor normally drives the wash basket with a multi-ribbed belt. Simply remove the belt and try to start the motor again. If the motor turns normally then you should verify that the basket turns freely and does not have anything caught between it and the outer tub. We have control boards for thousands of models On electronic control models, the main control board operates the individual components of the washer including the fill circuit and the drive motor in the same manner as a manual timer model.

If the control board does not provide the proper voltage to the drive motor, fill valve, drain motor or door lock then the washer may not start. The main control board on most washers is complicated and difficult to diagnose without proper test equipment and procedures. You can visually inspect the control for signs of electrical arcing or burned or damaged components on the board. You should use caution when replacing a control board as sometimes the burned components are caused by external component failures. These will need to be identified and corrected before installing a new control board. Service should be attempted only by qualifies persons. We have washer parts for thousands of models We’ve identified the most common parts that can cause a washer to not start, but there are other parts that could be at fault. If you are unable to fix your washing machine with the information above, enter your model number into the search box for additional repair help. Searching with your model number will give you access to all parts and schematics, symptoms for your specific washer as well as all installation instructions and videos.