Install a towel bar on a bathroom wall or hollow door How to Install a towel bar on a bathroom wall or hollow door This two part how to video series demonstrates how to install a towel rod or towel rack (remember click on chapter two for the hollow door video instructions). In the first video, your instructor takes you through all the necessary steps of installing a towel bar: measuring, screwing, and assembling. The second video demonstrates how to hang a towel rod on a hollow door. Hollow doors require an extra step when hanging a towel bar. You need a few more tools, but the end result is a towel bar that is anchored nicely and looks good, too. Good information for remodeling a bathroom. Install a towel bar on a bathroom wall or hollow door - Part 1 of 2 Install a towel bar on a bathroom wall or hollow door - Part 2 of 2A towel radiator is a luxurious addition to your bathroom. You can choose from lots of designs, from simple ladders in white or chrome to stylish designer models, both of which are effective in providing heat in your home and warmer your towels.

You can fit them in the same way as a standard radiator. The easiest way to fit your new towel radiator is to replace a radiator of the same width. In that case there's no need to drain your system, or to take up your flooring and skirting boards. Simply turn off your heating, then isolate your old radiator by shutting off the valves on either side before removing it from the wall. Your new towel radiator will be connected to the existing pipework. But if you want to run chrome pipes to match a new chrome radiator, or your new radiator is a different width from the old one, you'll need to drain your system and make alterations to the pipework. This means you'll be able to choose from a much wider range of replacement radiators - and the job isn't too difficult to do with modern plumbing fittings, which are very easy to work with and need no heating or soldering. Make sure you drain the system before you begin, and remove your flooring and skirting as necessary to get to your pipework.

How to mount a new towel radiator Preparation You'll need to take off your old radiator and brackets and fill the fixing holes before you can put your new towel radiator up. Make sure that the wall and new fixings are strong enough to hold the weight of the towel radiator when it's filled with water. And remember to leave at least 20cm between the bottom rail and the floor. pipe and cable detector power drill with masonry or ceramic tile bits pipe wrench or waterpump pliers towel radiator with brackets and fixings pair of radiator valves 15mm copper or chrome plated copper pipe 2 telescopic extending radiator tails How to connect a towel radiator to the pipework For the best result, if you're fitting a chrome towel radiator, use a chrome-plated copper pipe to match. You can snap a chrome-effect pipe cover over the section of visible pipe which you're not replacing. Telescopic extending radiator tails will make it easier to get a precise fit.

Top tip - Upgrade your pipes You can give your old radiator pipes an instant makeover with chrome-effect plastic pipe covers. Simply cut them to length and snap them into place. Top tip - Upgrade your valve Even if you're not replacing the valve, you can often unscrew the old valve head and replace it with a new one. Start by fitting telescopic extending tails to the towel radiator inlet and outlet. You might find it easier to do this if you take the radiator off of the wall.Measure Bay Window Vertical Blinds Fit a compression elbow joint to the telescopic extending tail on the radiator inlet. Auto Glass Repair Franklin NcThen cut a length of pipe to run from the new elbow to the existing radiator valve. Hotel With Hot Tub Oregon Coast

Remember to apply PTFE tape to the threads of compression fittings. Unscrew the old valve head and replace it with the new one, then remount your radiator. Use a suitable compression fitting to attach the radiator outlet to the pipework on the other side - you should only fully tighten the joints when all the pipework is in place and fits correctly. Then, holding each fitting steady with a pipe wrench or water pump pliers, tighten the compression nuts using an adjustable spanner. Make sure you don't over-tighten them, though. How to run new pipework to a towel radiator If you're planning to run new pipework to your radiator, you'll need to drain your system and expose the pipes. Make sure all your new pipe fittings are below ground level. When you've connected each side of your radiator, turn on your water and heating, and check it's working with no leaks before you replace your flooring and skirting. Wrap PFTE tape around the threads of the radiator valve compression joint and attach it to your radiator (you might find it easier to take it off the wall to do this).

Then remount the radiator. Use a mini pipe cutter to cut through the hot water supply pipe. Then clean the cut end with wire wool. Attach a push-fit straight coupler. Then measure and cut a short length of pipe to extend the supply pipe as far as the inlet of your new radiator. Measure and cut a section of chrome-plated pipe to run from the radiator inlet down to the supply pipe. Connect the horizontal and vertical sections of the new inlet pipe, using a compression elbow joint. Remember to put some PTFE tape on the threads. Repeat the process to connect your radiator to the pipework on the other side.A towel bar is a handy fixture for any bathroom. It provides a place where you hang your towel so you can grab it with ease after a bath or shower. Placing your towel on a bar also ensures it dries quickly. These bars add some style to any bathroom as well. If you do not have a towel bar or if you have one but it is loose or broken, then you should purchase a new one. Some people may think mounting a towel bar is difficult.

However, with the right tools and the ability to follow instructions, you can install one without any professional help. Before you hang the towel bar, make sure you know what type it is, as it may require a different type of installation. Read the directions included with the product to determine the best way to mount it. In some cases, you might not even need to mount the bar. Type of Towel Bar Up to 18 inches in length Accommodates face and hand towels Up to 24 inches in length Accommodates face, hand, and bath towels Comes in a variety of sizes Comes in different sizes May be freestanding or require mounting Some models have towel warmers You should choose a towel bar based on your needs. In some cases, you might need more than one type of towel bar. Some people want to have a full-sized bath towel bar next to their shower or tub, as well as a hand towel bar next to the sink. In some bathrooms, it is easy to find the right place to mount a towel bar.

Usually, a bath towel bar should be within arm's reach of the shower or tub. However, you should consider a few things. First, the towel should not block access to light switches, electrical outlets, or other things in your bathroom that you need to use. The towel bar should also be at the right height. It should be high enough that the towels do not touch the floor, while low enough for everyone to reach. Another consideration with location is wall studs. Hanging your towel bar on studs ensures that it stays in place and does not damage your walls. Use a stud finder on your bathroom wall. You might be able to find a stud for one end of the bar, but not for the other. In such cases, you need an anchor when you install the bar on the end without an accompanying stud. The towel bar itself does not mount onto the wall. Rather, you must install the brackets first and then mount the bar. There are two different steps to doing this. First, if you have a stud behind the area where you plan to put the anchors, all you have to do is place the brackets in place, and then drive the screws into the wall to hold them up.

Measure the wall and mark where you want to put the brackets with a pencil. Use a level to make sure the brackets are straight. However, if there are no studs in the wall, you must first drive in some anchors to prevent damage to your walls and ensure the brackets stay up. Use a drill bit that is a little bit smaller than the anchor to make holes. Then, place the wall anchors inside and gently tap on it with a rubber mallet or hammer until it is all the way inside. Install the brackets using the anchors. This last step may vary depending on the type of towel bar you purchased. Some models simply slip on top of the brackets. If your towel bar kit comes with an Allen key or hex wrench, then you can tighten or loosen the bar as needed. Slide the bar into the brackets and search for the hole where the small wrench fits, and then tighten it. If the bar feels loose after a few weeks or months, just use the same wrench to tighten it once again. To find the right towel bar on eBay, just use the search engine, which resides on every site page.