How to Remove a Stuck Tub Spout Tub spouts will eventually either stop functioning properly or begin to lose their coating, making them look old and worn. Since many tub spouts function without incident for years or even decades, you could experience no difficulty when you attempt to remove the spout. Sometimes the solution is as simple as removing the retaining screw from the spout, while other times you must use certain tools to remove the spout. Examine the bottom side of the spout, close to where it meets the wall or side of the tub, using a flashlight. If the spout has a small hole or notched-out section on the end, it is secured to the water pipe with a retaining screw. Place a towel over the bathtub drain, then insert an Allen wrench into the hole or notched-out section and turn the retaining screw counterclockwise until you remove it. If the spout does not slide off easily after you remove the screw, twist it left and right as you pull on it for several minutes.

Wrap a hand towel around the tub's spout if you do not see a small hole or notched-out section. Clamp a pipe wrench over the towel and turn the wrench and the spout counterclockwise to remove it from the water pipe. Heat up the spout using a hair dryer if it will not come off the water pipe, causing the spout to expand slightly. Wear protective gloves when handling the spout after you have heated it up. Family Handyman: How to Replace a Bathtub Spout "This Old House Magazine"; Replace a Leaky Shower Diverter; Bathtub diverters sit in the tub’s faucet, where you must pull up on the post on the top of the spout to... How to Take Off a Spout That Is Stuck on an Old Tub; How to Remove a Stuck Tub Spout; How to Remove an Old Tub Spout; Get Ideas Easy-to-Make Wreath Chandeliers... Another problem can be that your handle is stuck from soap scum buildup or ... Even though a bathtub's spout does not... How to Remove the Spout Cap From a Delta Kitchen Faucet;

How to Replace an O-Ring in... How to Take Off a Spout That Is Stuck on an Old Tub. Home Maintenance & Repair; How to Remove a Kohler Tub Spout How to Remove a Delta Tub Spout How to Remove a Faucet SpoutYOU ARE HERE: LAT HomeCollectionsBrassUsed Furniture Store Boise Id QUESTION: I want to replace a corroded bathtub spout, but it won't unscrew. English Bulldog Puppies For Sale In Missouri CheapThe spout is connected to copper tubing, so I'm concerned about applying too much force and possibly twisting the copper pipe. Powerful Indoor SpotlightsHow can I safely remove the spout?Merle Henkenius, a plumber and author in Lincoln, Neb., answers:ANSWER: The spout is connected one of three ways. It could be a simple slip fitting held in place by a hex-screw fastener on the underside of the spout;

this is an easy thing to miss. Check the underside, remove the screw if you find one, and slide the spout off with a slight twisting motion.The spout could also be threaded onto a copper male adapter soldered onto the pipe. Or it could be threaded onto a nipple connected to a 90-degree brass drop-eared L-shaped fitting inside the wall. Either way, it shouldn't be that difficult to loosen.If the spout is threaded on, you're probably being too cautious. The first step is to cut through any caulk between the spout and wall. Then grip the spout near the wall with a 10-inch pipe wrench and try again with a little more gusto. Push counter-clockwise, using steady pressure.If that approach doesn't work, you'll need to cut off the spout with a hacksaw. Start by sawing off the spout end just behind its opening. If that exposes the threads where the spout joins the nipple, cut diagonally across them with the hacksaw; try not to cut into the nipple. After severing the threads, twist off the spout.If cutting off the tip doesn't expose any threads, cut through the spout about 1 inch from the wall.

Look for the threaded connection, saw through the threads--again, don't damage the nipple--then twist off the spout.Replating Can Be Expensive and RiskyQ: My home was built in 1930. The antique brass doorknobs and faceplates on all the doors are worn. This hardware is unique and I don't want to replace the pieces. Can they be refinished or replated? If so, how do I find a reputable company?John Christou, vice president of George Taylor Specialties, a New York City-based dealer and manufacturer of reproduction hardware, suggests:A: If the hardware is solid brass, the protective lacquer coat may be gone and the "wear" you see could be tarnish. In that case, have any remaining lacquer stripped off and the brass polished and relacquered. If the hardware is brass-plated steel and the plating is wearing off, polishing will only make things worse.Replating is an option, albeit an expensive one. If the pieces are valuable antiques, they might be worth it. Otherwise, get an estimate and compare it to the cost of replacing the parts with reproduction pieces.

To give you an idea, the average cost for our reproduction doorknobs is $15, and $10 to $20 for faceplates.If you decide to replate, keep the following in mind:A poor replating job can destroy the value of an item. To find a good replater, check with the managers of motorcycle and automotive speed shops. These people usually are fanatical about quality work. Antique dealers can also refer you to a reliable plater.Replating will highlight surface flaws rather than hide them. If possible, have flaws polished off before replating--without polishing off engravings or stamped dates or numbers.Make detailed drawings or take photos of all the parts. These visual records will come in handy when it's time to put everything back together, especially if the replater loses a part.3 Methods Can Fix Slippery New RampQ: We built a wooden ramp up to the front door of our new home, but it's very slippery when wet. How can we make it less dangerous?Tom Philbin, a former painter and author of three books on painting, explains:A. There are a number of effective ways to make a ramp less slippery.