We have two bulbs in our house that need replacing. They appear to be PAR38 bulbs. The bulbs are both in recessed sockets. There is not enough space between the bulb and the well to get fingers around. The bulbs are in too firmly to budge with what little torque we can exert from the face. Obviously, we don't want to try anything that would break them. A Google search for "bulb changer" yields some promising results, but I figured I'd ask some humans to be sure. Take a piece of duct tape and wrap it in the shape of an "O", with the sticky side of the tape on the outside. Stick the loop of tape to the face of the light bulb such that it is secure. Put your hand (four fingers) inside the loop and twist counterclockwise to loosen the bulb. Get a light bulb changer pole at your local home improvement store or your favorite hardware store. The ones with suction cups are best for flood lights, where the face of the bulb is a little flatter, but might have a tougher time gripping smaller, rounder light bulbs where you need something that can fit up inside the fixture and grip the sides of the bulb.

The same applies for CFL's or LED "bulbs" that may not have a uniformly smooth round surface. And with the extending pole, you can use something like this on an 8ft celing or a 12ft ceiling without climbing to the tippity top of a free-standing ladder. Another trick is to pull the trim out with the bulb but not all trims connect the same. Some use springs, some clip into a socket, while others are sealed. But usually works for me because I do it all the time. There's a company that makes suction cup hooks/hangers. You put the suction cup on an object and swing the hook. I'll bet you could attach one of these to the glass and use it to unscrew the bulb. I found this on Amazon. Edit: if the bottom of the bulb is highly curved, this won't work. The surface has to be flat or only slightly curved. Use oven mitts with silicone grips Works like magic for opening light fixtures, changing light bulbs, opening jars, and so on. If you don't have silicone oven mitts, you can try a silicone baking mat.

Just push the mat against the face of the light bulb and unscrew it. Do you have a glass/cup with a similar circumference? If so, stretch the wrist of a latex glove around the rim. Fit the rim of the cup around the bulb and twist. In my experience many times bulbs of this nature tend to, separate from the metal seating as you apply the pressure needed to twist them out. If this becomes the case usually the glass can be removed carefully, while turning slightly to snap any filament that may be still attached to the glass.Mobile Homes For Sale Lemoore Ca Power Off and as suggested use pliers to ease the metal seating out.Homes For Sale Washington Street Babylon Ny (Safety Glasses- its very likely TINY dust sized pieces of glass will be almost, 'Floating' around-trust me). Shower Drain Flange Replacement

If you haven't satisfied your original question on how to approach, here ya go, drug, hardware, dollar stores and ANY online market place sell, 'Super Stick Gel Pads'. They can be oval or square, approximately the size of a large smartphone, and are easily cut to size. They have endless uses, and this is one, as they stick without waiver, yet can be pealed back easily, rinsed and reused. The cost is usually under $5 for a 3 pack, and then very simply slide it up with 2 wooden Paint stirrers,or even small popsicle sticks- 2 3, 4 whatever gives you a safe feeling of pressure and maneuverability. Maybe small size -2 on opposing sides using 2 hands etc. If the bulb breaks, nearly all the pieces small or large will stick to the gel pad, & rinse off as well. It will stay attached to the bulb if you need to switch 'Implements', to say a simple pair of pasta or grill Tongs. Even your palm will be adequate and protected (not so crazy I've removed 100's of bulbs). wrap the bulb in saran wrap or equivalent.

It will provide a great grip and reduce risk of flying fragments should the bulb break. Wear a protective glove and glasses too. Use your vacuum cleaner. With the vacuum turned on, place the hose or extension tube on the light bulb, turn the tube and the light comes out. The same principle can be used to reinstall the replacement bulb. I use a suction cup dent puller to grip the glass on computers and tablets when there's no handle: I doubt that glass is much different than the glass in the stuck bulbs, strength-wise. I've done this using long nose pliers for the first few turns, until there were enough millimeters free to grab it with fingers. You have to be very, very gentle with them. I wouldn't use them on CFL bulbs because they are toxic when broken. But if you don't have the other tools suggested and the duct tape doesn't work, they are worth a try with a normal bulb, even though there is some risk of breakage. Provided the light-fitting is accessible, use rubber gloves.

It works every time! The problem with using a vacuum cleaner or long pole is the chance of dropping the bulb before you get hold of it and there's no need to break the bulb to get it out. Duct tape works fine. Form a small piece of duct tape in the shape of a T, with the outside of the top of the T sticky. The bottom stem of the T is what you hold onto. The top of the T sticks to the bulb and you can turn it easily. Cut a potato in half and stick one end into the broken bulb and twist. By posting your answer, you agree to the privacy policy and terms of service.How to Replace Indoor Floodlight Bulbs in the Ceiling Track lighting and recessed ceiling lights sometimes use floodlight bulbs instead of standard bulbs. Floodlight bulbs offer more light in a concentrated area. Most indoor floodlight bulbs screw into a socket much the way a standard bulb does, although some have pins, similar to a side marker bulb for a car. When replacing indoor floodlight bulbs in the ceiling, it is a good idea to remove the old one first.

This helps to ensure that you purchase the correct size and type of floodlight for your ceiling fixture. Find the circuit breaker to the lighting system inside your home's electrical panel box, and turn the circuit breaker to the "Off" position. Place a stepladder or a step stool under the ceiling fixture so you can reach the floodlight bulb comfortably without overstretching. Remove any trim from the fixture, if you are replacing a floodlight bulb in a recessed ceiling fixture. The trim either has screws, requiring a Phillips-head screwdriver to remove them, or simply turns counterclockwise until the connecting tabs release. If you're working on track lighting, position the fixture so it is pointing straight down. Turn the floodlight bulb counterclockwise with your fingers until it completely unscrews from the light socket. Some floodlights use two pins instead of screwing into a socket. If the bulb stops once you turn it counterclockwise a quarter-turn, pull the bulb down slightly.

Pin connectors will release without much effort. Replace the floodlight bulb with one that is the same size and has the same connection. Push the pin-type floodlight bulb into the socket and turn the bulb clockwise until it locks in place. If you have the standard screw-in-type floodlight, twist it clockwise until it stops. Reconnect any trim pieces either by twisting them back into the fixture or reattaching them with retaining screws. Turn the circuit breaker back to the "On" position once you finish. If you cannot get your fingers around the side of the floodlight bulb to remove it, fold a 12-inch piece of duct over itself with the sticky side facing out. Stick the tape on the center of the bulb, and use the tape as a handle to begin unscrewing the bulb. Home Depot: Bath LightsLoosening Recessed Light Bulbs; 19 Home Decor DIYs That Only Look Expensive How to Change a Recessed Light Bulb How to Remove a Small Recessed Floodlight How to Replace Track Lighting Bulbs