Posi-Temp Pressure Balanced Shower Cartridge Widespread Bathroom Faucet Rough-In Valve with Drain Assembly Rough-In Posi-Temp Pressure-Balancing Cycling Valve Tub/Shower Drain Covers in Brushed Nickel Tub/Shower Drain Covers in Wrought IronWidespread 2-Handle High-Arc Bathroom Faucet Trim Kit in Polished Brass (Valve Sold Separately) Voss 1-Handle Posi-Temp Shower Trim Kit Less Showerhead in Oil Rubbed Bronze (Valve Sold Separately) Wynford Single-Handle 1-Spray Moentrol Tub and Shower Faucet Trim Kit in Brushed Nickel (Valve Sold Separately) Circular Drop Ell in Brushed Nickel Basket Strainer in Stainless Steel Voss Posi-Temp 1-Handle Tub and Shower Trim Kit in Oil Rubbed Bronze (Valve Sold Separately) 90-Degree 1-Handle Volume Control Valve Trim Kit in Chrome (Valve Sold Separately)Shower faucet cartridges can be especially difficult to pull. Al Moen invented the cartridge faucet, and cartridge faucets remain a specialty of the Moen company.

The company designs them to be removable so you easily can replace rubber gaskets and O-rings that may be causing leaks. Unfortunately, these rubber parts often stick to the valve housing and make removing the cartridge a challenging job. Moen sells a tool that makes pulling cartridges easier, but sometimes you need more help than that. Cartridge Removal Procedure The usual procedure for removing a cartridge is to unscrew the handle, and after turning off the water, pull out a retaining clip. In the best of circumstances, you then grip the cartridge stem with pliers and pull, and the cartridge should slide right out. In less than ideal circumstances, however, the cartridge won't budge, no matter how hard you pull -- and you begin looking for ways to gain more leverage. Before trying other pulling methods, however, it's wise to douse the cartridge with white vinegar and wait for an hour or two. It safely dissolves mineral deposits that may be binding it. Using a Cartridge Puller When the cartridge doesn't come out, even after treatment with white vinegar, you have occasion to make use of a tool that Moen manufactures for pulling stuck cartridges.

The T-shaped tool fits over the stem and seats against the cartridge housing. After screwing its bolt into the cartridge stem, rotate the handle to loose the bonds holding the cartridge so you can pull it out. If the cartridge is old and stuck enough, however, you may end up pulling out the cartridge shaft and leaving the sleeve stuck in the housing. You need to remove the sleeve before you can insert a new cartridge. Pulling Out the Cartridge Sleeve Plumbers confronted with a stuck cartridge sleeve have developed an effective method for removing it. You first cut threads into the inside of the sleeve with a 1/2-inch tap. The sleeve is made of brass, which is easy to thread. You then insert a 3-by-1/2-inch hardened steel bolt through the holes of three or four stacked 1-inch washers, and screw the bolt into the threads. When the bolt is deep enough so its head wedges the washers against the cartridge housing, tightening it with a wrench loosens the cartridge enough for you to pull it out.

Considerations You don't always have to resort to a cartridge puller, especially when you're removing a cartridge from a sink faucet. Reattaching the faucet handle after you pull the retaining pin often gives you the leverage you need. Mini Ash Vacuum CleanerDepending on the configuration of the faucet and wall or backsplash, you may be able to hook a pry bar behind the handle, support it against a piece of wood and pry the cartridge. T Shirt Manufacturing Companies In KolkataIt often takes only a small movement to break the seal so you can remove the cartridge by pulling on the handle. Outdoor Ping Pong Table Sports Authority Easy to install and completed within minutes Quickly repairs leaky faucets and drips

The MOEN Single-Handle Replacement Cartridge works with all MOEN single-handle faucets excluding Posi-Temp and ExactTemp styles. The cartridge is made with cast metal and plastic for strength. Includes twisting cap to loosen installed cartridge Will not work with MOEN Posi-Temp and ExactTemp faucets Limited 1 year warranty 4 Moen Kitchen Faucet cartridges (purchased at home depot) replaced now handles turn wrong way (out) to turn water on. Moen Kitchen Faucet cartridges (purchased at home depot) replaced now handles turn wrong way (out) to turn water on. 3 What is the difference between Moen 1225 and 1225b cartridge? 3 what is the differance between a Moen 1200 and a 1225 faucet cartridge ? 3 Do you carry the U- shape lock pin for this moen cartridgeWhat are some tips for Moen shower valve repair? To repair a Moen shower valve that is either leaking or not balancing the cold and hot water correctly, begin by replacing the shower valve cartridge.

A Moen shower valve cartridge has different working parts that malfunction with time. Replacing the cartridge can solve a number of problems. What are some shower repair tips? Where can you find a Moen shower faucet manual? How do you replace a Moen shower cartridge? Before removing the old cartridge, shut off the water to the house and turn on the faucet in the bathroom sink to drain any water remaining in the pipes. Although a Moen cartridge puller is not necessary, it can make removing the cartridge easier. Remove the faucet handle, the handle collar and adapter and the retention clip, in that order. Loosen and remove the cartridge to check for debris. Clean it as required, and insert the new cartridge. Reassemble it in reverse order. Is it possible to get the Moen shower faucet manual for free? The Moen shower faucet manual is free. It can be obtained through the customer support page on Moen's website by entering the model number of the shower fa...