How do you repair a Delta shower faucet? Repair a leaking Delta shower valve by replacing the cartridge. Prior to starting the repairs, shut off the water supply at the main. Most repairs can be done without cutting through the drywall behind the valve. Where can you buy parts to repair a Delta shower faucet? How often should you service a Delta faucet? Protect the tub by placing an old towel over the drain. This also prevents any small pieces from falling down the drain. Remove the decorative cap from the valve handle and the screw that holds the handle on the stem. Pull the handle from the stem, and loosen the screws that hold the trim in place. Remove the plate to expose the valve, and slide off the outside sleeve. Use water pump pliers to remove the brass bonnet nut from the assembly. Remove the plastic plate from the valve, and pull the cartridge out of the assembly, using a slight wiggling motion, if necessary. Delta uses several different styles of assemblies, so take the old one to the home improvement or plumbing store to ensure purchase of the correct replacement.

Clean the inside of the valve, removing all debris. Push the new valve in place with the side marked Hot to the left. Once it is firmly in place, install the new limit stop by following the manufacturer’s directions. Replace the bonnet nut, and turn it until snug using the pliers. Reassemble the valve, and turn on the water. What are some common repairs for a leaky bathroom faucet? Some common repairs for a leaky bathroom faucet include replacing the washer in compression faucets, the O-ring in compression and cartridge faucets, and t...Hot Tub Motels Nj How do you remove a Delta round stem valve?Rural King Carpet Cleaner Rental To remove a Delta round stem valve, first shut off the water supply to the house and turn the faucet on to flush out any remaining water. Yellow Gingham Check Curtains

How do you repair a leaky Delta bathtub faucet? To repair a leaky Delta bathtub faucet, replace the worn rubber seats and springs. If the faucet has a handle for each temperature setting, feel the temper... What is a plunger can? Where can you find pictures of French drains? What are some tips for installing a kitchen sink drain? How much does it cost to build a concrete septic tank? What is the average cost of a bidet toilet? Why won't my shower work?Install It Yourself You no longer have to tear down the shower wall to get your dream bathroom. Install a new tub and shower in just an hour. Universal Tub & Shower fits a variety of valves from Pfister®, Delta®, or Moen®, saving you time and money. Save Time & Money HGTV Designer Lisa LaPorta Updating your bathroom is easy with Universal Tub & Shower. Interior designer Lisa LaPorta shows you how. Upgrading Your Tub & Shower is Easier than Ever. This innovative upgrade kit is designed to fit 8 commonly installed valves from Pfister®, Delta®, and Moen®.

Eliminating the need to replace your valve, Universal Tub & Shower helps save time and money. Delta® 600 Series Diamond Delta® 600 Series Round Stem Upgrade in 3 Easy Steps Check Compatibility Check Compatibility > How to Install > Available in a Variety of Styles & Finishes How much should it cost to replace a bathroom tub valve? I have a one knob shower faucet in my bathtub. It was leaking inside the wall right at the valve. I was told that to replace the valve and shower nozzle and all involved would cost $425.00 Is that reasonable? Angie's List>Project Cost Info It depends on how difficult it is to get to the valve... the value costs about $75 to $100, the rest is labor. If the value is readily accessible through the back of the wall, then this is too high.. but if the plumber has to remove and replace the tile or otherwise open the tub side itself, then is not unreasonable.If the valve is accessible from the other side of the wall, consider opening the drywall yourself and when the plumber is done replace the drywall and repaint yourself..

This should save you some money, if you are comfortable with doing this. also, this is not a difficult repair to do yourself if you are reasonably handy... turn the water off, open the wall from the back side, remove the value... Buy a value with the same plumbing configuration.. (Take the old valve to the store and check the configuration of the new value against the old.) Re-Install the valve Repair the hole in the wall. The prior comment suggested doing it yourself - that really applies only if it is connected to all pipes with threaded connections - many valves are soldered in, and shower valves are one of the toughest soldering jobs because of the large mass of metal in the valve, to do it without distorting the valve or damaging it.if threaded, be sure to get teflon plumbers tape to seal the threads, and check out a Youtube video on how to apply plumbers tape to the male threads to prevent leakage.On your $ question - $425 seems steep, IF accessible from the back of the wall.

If have to go through the valve hole in the surround or tile, then maybe in the ballpark, though still high unless you are in a big city like NY or Chicago or Boston - is quite a tricky maneuvering exercise from the front - commonly involves pulling it out by cutting the pipe from the floor below, soldering the new one, and putting the pipe back up from below into place, then soldering the top connection. My landlord just said it cost 600 dollars do just this and wants me to pay half! Answered 2 years ago i just replaced a shower valve for a customer. I had to tear out sheetrock from behind the shower valve. They had a cheepo depot valve with thread fittings and conveniently ran copper with water hammer arrestors and teed off with GALVANIZED which was clogged to the size of a coffee straw. I cut out all threaded fittings and soldered wirsbo pex connectors directly to the copper. The homeowner picked out a Delta faucet with adjustable pressure and temperature. The valve and trim package was $240 and comes with a lifetime warranty.

Homeowner was responsible for patchwork and gave them option to call a few people I use. Total bill was $390. Because of the difficulty involved, $425 is a fair minimum for parts and labor (depending on model). The person who said " this is not a difficult repair to do yourself" obviously underestimates his skills and assumes every one possesses similar tallent. Most older homes have souldered plumbing, so unless you have sufficient souldering skills I recomend leaving it to the pro's (including high quality Handy men)No body mentions anchoring the fixture body and pipes which can be difficult and time consuming. Every replacment is different and (in my opinion) requires an on site evaluation with consideration given to make and model before offering a price.My services are turn key, no need to call for Dry wall repair, Painters or Tile repair person, I do it all with quality. I love my job Answered 9 months ago Again a lot depends on what kind of plumbing you have and what kind of new valve is going in and how hard it is to get to keep in mind unless you just want a newer model 9 times out of ten you can fix the valve by repacking it for much less then the cost of replacing it most contractors want you to replace it because they know they will make more for that

Answered 2 months ago Hi my name is Matt and I am a plumber people get us confused with handy men a lot the prices are a lot difrenet, but keep in mind are prices are the way they are for the following reasons. A bad plumbing job by a handyman in the end will cost u much more then if u spent the money and hired a real plumber who does it right. See plumbing is all I do and I have many years experience. Water is not something to mess with if u don't know what u are doing bc in the end if it's messed up u will have leaking pipes in ur walls. This could cause lots of money in water damage, and you could ever have health problems(mold). I would never go to the doctor to have my cavity filled so why people try to get someone to do plumbing who is not licensed and been doing this is beyond me. Save ur self the money, stress, and risk call a real plumber. To answer the ? That's just about right $425 if it's cut and dry if it's a difficult job and not easily accesable then more like $725.