With all the moisture and soap scum, bathrooms can get grungy in a hurry. To keep your bathroom clean and germ-free requires frequent cleaning. But it doesn’t have to be a chore, especially if you enlist the help of your family and ask everyone to wipe down sinks and showers after they use them. It only takes a minute or so. And don’t forget to run the exhaust fan or crack a window during and after a steamy shower. Here’s how to make your bathroom surfaces sparkle from the experts at Consumer Reports who share their advice in "How to Clean Practically Anything." The material of a tub and sink determines how you clean it. Check the manufacturer’s guidelines. As a rule, never use abrasive cleaners, such as scouring powders or steel wool on acrylic, fiberglass, or sealed-marble tubs and basins. Instead, use a sponge to clean them with hot water and liquid detergent. Use a little extra detergent on stubborn dirt and grime. It’s usually safe to clean tubs made of vitreous or porcelain enamel with scouring powder and warm water.

Because cleaning solutions can stain an unglazed enamel surface, test them first in an inconspicuous spot. The material of the tub and sink also determines how you treat stains and scratches. Remove small scratches from acrylic with a plastic polish that’s sold for this purpose; Multi Family Homes For Sale In Brookfield Ctbuff with a clean cloth and rinse. Made To Measure Silk Roman BlindsUse ultrafine sandpaper to remove stubborn stains from solid-surface synthetic tubs and sinks, and buff with a clean cloth. Cost Of Floor Tiles In UgandaRegularly apply a sealer to marble and other stone surfaces to prevent staining. For stains on vitreous or porcelain enamel, apply a solution of ½ cup of chlorine bleach in one gallon of water, leave on for a minute or two, then rinse.

Blue-green stains on enamel surfaces are a telltale sign of a continually dripping faucet. After fixing the leak, rub a paste of borax and lemon juice onto the stain. Leave it on for several minutes, scrub with a plastic scrub pad, rinse with warm water, and buff dry. To prevent soap and dirt from building up on surfaces, wipe down or squeegee shower walls and doors each time the shower is used. Or spray on a special shower-cleaning product that’s intended for use after every shower. Clean showerheads regularly with cleanser to prevent deposits from building up. If a metal shower head becomes clogged with scaly deposits, place it in a pot to which you’ve added a solution of one part vinegar to eight parts water, bring to a boil, and simmer for about 15 minutes. Soak a plastic shower head in a solution of equal parts vinegar and hot water. Scrub grout with a toothbrush dipped in a solution of ½ cup bleach and a gallon of water. Today’s faucet finishes are easier to care for.

You can make them sparkle by removing marks and smears with a soft cloth or a sponge dipped in warm water and dishwashing detergent. Dry with a soft, clean cloth to restore the shine. On older faucets, gently remove any rust spots with steel wool or a commercial rust remover, but make sure the cleaning product isn’t too abrasive. Then wash the surface with mild detergent and warm water. Dry with a soft cloth and apply a thin coat of solvent-based polyurethane to protect the chrome from moisture that might cause further rusting. Lime deposits often build up on chrome bathroom fittings. Clean first with detergent and warm water, then wrap the chrome with a cloth soaked in white vinegar or a commercial descaler. The deposits should soon dissolve. Use a commercial glass-cleaning product or one part ammonia and eight parts water, and wipe dry with a damp, lint-free cloth. Polish with a microfiber or other lint-free cloth, or dry with a squeegee. In areas where mirrors tend to fog up such as the bathroom use a product (formulated for automobile windshields) that contains an anti-mist chemical.

Remove hairspray residue with a cloth dampened with rubbing alcohol. Brush the toilet bowl regularly to remove any stains and hard-water deposits, making sure to clean beneath the rim. Clean the brush afterward by leaving it in the bowl while flushing the toilet. Once a week, use the brush to clean the bowl with a disinfectant cleanser you’ve poured into the water, making sure to clean the brush by running it through the soapy water, then rinsing it during a flush. Use a sponge dipped in a solution of hot water and disinfectant cleanser to wipe down the rest of the toilet and the toilet seat. Share your cleaning tips. Operation - Kitchen Sprayer and Hose Operation - Water Pressure Operation - Water Temperature Can drain openers cause damage to finishes? How can I clean and/or remove mineral deposits from my showerhead? Touch-clean® Showerheads - wipe the face of the showerhead (rubber nubbins) to loosen and break away deposits. Non Touch-clean showerheads or stubborn deposits - unscrew the showerhead

and soak it in a 50/50 vinegar and water solution for several hours. stubborn deposits, rub with a toothbrush. How can I remove mineral deposits from my aerator?Soak it in vinegar overnight then flush with water. How should I clean or maintain the finish on my faucet?Hard water stains may be removed using a 50/50 solution of white vinegar and water. What cleaning products can cause damage to finishes? Was this answer helpful? Is your shower head not performing like it used to? Over time, mineral deposits can build up in your shower head. This can cause the nozzles to squirt water in all directions or clog up completely, leaving you with poor water pressure or low flow. Here are our top tips (listed from easiest to more complex) to help get your shower head back to peak performance. Many shower heads have flexible rubber nozzles. You can dislodge mineral buildup in these nozzles by simply massaging each nozzle with your finger. You can also try gently scrubbing the nozzles with a toothbrush.

There are a couple ways to do this: To clean the filter screen, you may need to consult the shower head instruction manual. If you didn't keep the manual, don't panic! You can usually find it on the brand's website or by contacting the customer service department. In general, the filter screen is located in the part of the shower head that connects to the pipe. You will need to remove the shower head from the pipe to get to the filter screen. In most Waterpik® brand shower heads, the filter screen can be removed by gently brushing the filter out. Or you can use tweezers/needle-nose pliers to get the screen out of the pivot ball. Once the filter screen is out of the pivot ball, run the screen under water for a few minutes to flush out any buildup. You can also use a toothbrush to gently brush out mineral deposits. Place the filter screen back into the pivot ball and re-install the shower head to the shower pipe.Harsh cleaning chemicals may damage your shower head and are not recommended for cleaning.