Faucets are important for convenience and decoration in kitchens and bathrooms. A faucet simply is a valve that controls the release of water into the sink. Many makes of kitchen and bathroom faucets are available, and among these, Moen is one of the most well-known brands. Alfred M. Moen started this company, and buyers recognize Moen as one of the best water fixtures. Moen products add style and grace to kitchens and bathrooms, and users experience their durability and quality. These faucets leak when they wear out or the cartridge gets dirty or corroded, so buyers need to know about the design of Moen faucets and the required steps to repair them. Moen concentrates on product designs that are beautiful and durable. The company offers a variety of sink, bathroom, and kitchen faucets, so buyers can select designs that match their home decor. Most faucets are of single handle design, though some have double handles. The designs have used simple cartridges since 1960s. The company calls this cartridge the Moen 1225.

It is a plastic cylinder 4 inches long and 3/4-inches in diameter. The cartridge is the engine of most single handle faucets and Moen has revised its design at least two times. Even after revisions, the newer version of the cartridge remains compatible with the older faucets. In single handle designs, pull the stem of the cartridge through the handle to open the water supply and rotate it towards the left and right to get hot and cold water, respectively. Many users prefer to repair a leaking Moen faucet themselves without the assistance of a plumber. Moen faucets have a specific cartridge in place of a valve stem. This makes the repair process relatively easy. Repair the faucet using the following simple steps The first step is to turn of the shutoff valves, which is usually in the cabinet below the sink. Turn off this valve to stop the flow of water to the faucet. Rotate the knob in the clockwise direction until it stops. Next, turn on the faucet to run out any extra water inside it.

For a faucet with two handles, isolate the leak to one handle and work on the cartridge of that handle. Look for a screw that holds the handle in place. If it is visible on the outside, unscrew it with a Phillips screwdriver. In many designs, the screw is under a plastic cap. Remove the cap with a slot screwdriver or a sharp knife. Faucets with a metal lever handle have the holding nut under the handle. Baby Furniture Stores Boro ParkUse an Allen wrench to unscrew it. Miele Washer Dryer DoorLift off the handle.Auto Repair Shop Las Pinas Moen faucets have a nut that holds the cartridge in place. Unscrew the nut with channel locking pliers. Wrap a cloth or rag around the nut to prevent damage to the finish. In some designs, a pin holds the cartridge in place.

Pull the pin straight off with needle-nosed pliers. Now, reattach the handle to the valve stem and use it to pull out the cartridge. Alternatively, use channel locks to pull out the cartridge. Take a picture or make a note of how the cartridge sits in the valve or the faucet handle body to reinstall it correctly. Take off the O-rings around the cartridge with a slot screwdriver. Examine and replace them if they are worn out. Locate the rubber seals in the inlet holes of the valve seat. Take them off in a similar manner, and replace them if required. Clean the cartridge to remove mineral deposits, which can interfere with the flow of water. Spray a jet of water on the deposits, or chip them off with a screwdriver. For sticky deposits, soak the cartridge overnight in vinegar to dissolve them; wash them off in the morning. Replace the cartridge if it has cracks. Buy the correct replacement of the cartridge. Most buyers prefer a name brand replacement cartridge. Insert the clean or the new cartridge in the valve seat in the same way as the initial orientation.

Place the pin or the retaining nut back in position. Similarly, reattach the handle and turn on the water to test the faucet. The sellers of eBay provide a broad range of Moen faucets in many different designs. To begin your search, enter the keywords, "Moen faucet" in the search field. You can find faucets available either individually or in sets. Select from a large number of categories and subcategories to narrow down your search to the desired type of faucet. Different products required to fix a leaking faucet are also available. Enter the appropriate keywords for the search. Moen faucets add an attractive designer touch to your kitchens and bathrooms. Users find it very easy to repair them at home with a few replacement products and a little know-how.Once upon a time, not so many years ago, it was easy for any amateur to repair leaking faucets.The job could be done with a screwdriver and a wrench. All you needed to do was replace an inexpensive little rubber washer. The job took five minutes.

You could find instructions in any decent how-to book.My, how times have changed.If you've tried to repair a leaking faucet recently, you've entered a confusing world of cartridges, swiveling balls, tipping valves, ceramic disks and a menagerie of little rubber seals that come in a galaxy of shapes and sizes. A job that used to take minutes has turned into a veritable quest that starts with a game of 20 questions designed to determine just what kind of equipment lies concealed inside your innocent-looking fixtures.It's enough to make your average amateur handyman ask: Is this progress?Plumbing historians agree that the man who did most to usher in the modern era of faucets is Al Moen, who is responsible for perhaps the biggest advance in water handling since the great Thomas Crapper invented the flushable toilet. The tale of Moen's moment of discovery has been passed down from plumber to apprentice for years.The story begins in 1937, when Moen was a college student who worked nights in auto garages to pay his tuition.

One day, when he needed to wash his greasy hands, Moen turned on the hot water. He almost burned his hands when the water became hot unexpectedly quickly. In a classic "Eureka!" insight, Moen saw the need for a single-handle faucet that could control the hot and cold water with one motion.It took Moen a decade to design, perfect and manufacture his faucet, which replaced the old washers, valve seats and stems with a single washerless cartridge. Moen's award-winning invention was delayed by several interruptions (including World War II), but its 1947 introduction greatly speeded the washerless revolution. Soon, several other inventors and companies introduced replacements for the old-fashioned washer-style faucet."I can't believe it took so long. It's such a logical invention," said David Lingafelter, vice president of marketing for Moen Faucets and Sinks headquartered in North Olmsted, Ohio. Lingafelter said that Moen and its main competitor, Delta, sell the majority of faucets in the United States.

When you add in the fixtures sold by other types of washerless faucet manufacturers, relatively few washer faucets are sold anymore.Don't people complain about the loss of simplicity?"Professional plumbers don't," Lingafelter said. Although washerless faucets require a bit of extra training to install and maintain, they last much longer, he said. Moen-style faucets contain all the moving parts and seals in a single unit, which usually can be replaced faster than removing and replacing all the guts in a washer-style unit, he said.Two professional plumbers asked to comment on the situation agreed with Lingafelter.", which features Love's humorous insights into subjects ranging from low-flow toilets to the high-tech fixtures in the new mansion of Microsoft founder and chairman Bill Gates.Love's an enthusiastic fan of the washerless world. "My mother has washerless faucets in her home that have been working since 1962," he said, adding that washer-style fixtures require much more frequent maintenance."

Replacing a washer will fix many faucets, but then there are the stem packings that can wear and the stems themselves that can wear," he said.Yes, it was cheap to repair a washer, but installing a new valve seat could be a pain," Carter said.Carter did offer some advice for avoiding the problem of trying to guess what kind of replacement hardware you need to repair a leak."The smart thing to do is buy a replacement cartridge at the same time you buy the faucet," he said. "Tack the packages up inside the vanity or sink cabinet, and you are good to go for 20 years."The reality of modern fixture maintenance is that the first thing you've got to determine is exactly what kind of equipment you own. If you take this information to most home centers, the sales staff usually can provide new parts, good advice and free pamphlets with step-by-step replacement instructions. The newer how-to books may include information on your hardware, and if you're really lucky, you'll even find videos that show how it's done.